Online citations, reference lists, and bibliographies.

Determination Of Orthotropic Bone Elastic Constants Using FEA And Modal Analysis.

W. R. Taylor, E. Roland, H. Ploeg, D. Hertig, R. Klabunde, M. D. Warner, M. Hobatho, L. Rakotomanana, S. Clift
Published 2002 · Engineering, Medicine

Cite This
Download PDF
Analyze on Scholarcy
Share
Finite element models have been widely employed in an effort to quantify the stress and strain distribution around implanted prostheses and to explore the influence of these distributions on their long-term stability. In order to provide meaningful predictions, such models must contain an appropriate reflection of mechanical properties. Detailed geometrical and density information is now readily available from CT scanning. However, despite the use of phantoms, a method of determining mechanical properties (or elastic constants) from bone density has yet to be made available in a usable form. In this study, a cadaveric bone was CT scanned and its natural frequencies were measured using modal analysis. Using the geometry obtained from the CT scan data, a finite element mesh was created with the distribution of density established by matching the mass of the FE bone model with the mass of the cadaveric bone. The maximum values of the orthotropic elastic constants were then established by matching the predictions from FE modal analyses to the experimental natural frequencies, giving a maximum error of 7.8% over 4 modes of vibration. Finally, the elastic constants of the bone derived from the analyses were compared with those measured using ultrasound techniques. This produced a difference of <1% for both the maximum density and axial Young's Modulus. This study has thereby produced an orthotropic finite element model of a human femur. More importantly, however, is the implication that it is possible to create a valid FE model by simply comparing the FE results with the measured resonant frequency of the CT scanned bone.
This paper references
10.1016/S0883-5403(08)80074-5
Computer predictions of bone remodeling around porous-coated implants.
T. E. Orr (1990)
10.1201/9781003068136-14
Bone remodeling around total hip implants.
P. Smolinski (1992)
Total Hip Revision Surgery
Galante Jo (1995)
10.1016/0021-9290(84)90029-0
A continuous wave technique for the measurement of the elastic properties of cortical bone.
R. B. Ashman (1984)
10.1115/1.2794181
Development and validation of a three-dimensional finite element model of the pelvic bone.
M. Dalstra (1995)
10.1016/0021-9290(91)90026-J
Development of a three-dimensional finite element model of a human tibia using experimental modal analysis.
M. Hobatho (1991)
10.1016/0022-460X(81)90387-4
Vibrational characteristics of the embalmed human femur
T. Khalil (1981)
10.1016/S0041-624X(96)00078-9
An ultrasonic method for measuring the elastic properties of human tibial cortical and cancellous bone.
J. Rho (1996)
10.1016/0021-9290(93)90001-U
ESB Research Award 1992. The mechanism of bone remodeling and resorption around press-fitted THA stems.
B. van Rietbergen (1993)
Modal Testing: Theory, Practice, And Application
D. Ewins (2000)
10.1016/1350-4533(95)97314-F
Relations of mechanical properties to density and CT numbers in human bone.
J. Rho (1995)
10.1016/S0021-9290(98)00018-9
Finite element modelling of the vibrational behaviour of the human femur using CT-based individualized geometrical and material properties.
B. Couteau (1998)
10.1097/00003086-199408000-00022
Correlation of Computed Finite Element Stresses to Bone Density After Remodeling Around Cementless Femoral Implants
H. Skinner (1994)
Bone remodeling around implants can be explained as an effect of mechanical adaptation
H. Huiskes (1995)
10.1115/1.3138589
A three-dimensional finite element analysis of the upper tibia.
R. Little (1986)
10.1016/0021-9290(90)90009-R
Three-axial strain controlled testing applied to bone specimens from the proximal tibial epiphysis.
F. Linde (1990)
10.1016/0021-9290(80)90188-8
Natural frequency analysis of a human tibia.
T. K. Hight (1980)
10.1016/0021-9290(93)90035-D
Frictional interface micromotions and anisotropic stress distribution in a femoral total hip component.
P. Rubin (1993)
Bone research in biomechanics
G. Lowet (1997)



This paper is referenced by
10.1155/2017/4539178
Macrodamage Accumulation Model for a Human Femur
Farah Hamandi (2017)
10.1038/s41598-019-43028-6
Neuro-musculoskeletal flexible multibody simulation yields a framework for efficient bone failure risk assessment
Andreas Geier (2019)
10.1007/s12668-019-00649-5
Significance of Orthotropic Material Models to Predict Stress Around Bone-Implant Interface Using Numerical Simulation
Pankaj N. Dhatrak (2019)
10.1007/S10237-004-0040-0
Can the diverse elastic properties of trabecular and cortical bone be attributed to only a few tissue-independent phase properties and their interactions?
C. Hellmich (2004)
10.1155/2017/8590251
Biomechanical Property of a Newly Designed Assembly Locking Compression Plate: Three-Dimensional Finite Element Analysis
Jiang-Jun Zhou (2017)
10.2174/1874325001004010152
Ninety-Degree Chevron Osteotomy for Correction of Hallux Valgus Deformity: Clinical Data and Finite Element Analysis
C. Matzaroglou (2010)
10.4028/WWW.SCIENTIFIC.NET/AMM.52-54.2088
Influences of Prosthesis Stem Lengths in Cementless Total Hip Arthroplasty
A. H. Abdullah (2011)
10.1063/1.5002384
Convergence and stress analysis of the homogeneous structure of human femur bone during standing up condition
Basirom Izzawati (2017)
10.1016/j.jbiomech.2010.03.034
Determination of the heterogeneous anisotropic elastic properties of human femoral bone: from nanoscopic to organ scale.
V. Sansalone (2010)
10.1016/j.jtbi.2009.05.021
Ductile sliding between mineral crystals followed by rupture of collagen crosslinks: experimentally supported micromechanical explanation of bone strength.
A. Fritsch (2009)
10.1371/journal.pone.0028868
Optimal Principle of Bone Structure
Yifang Fan (2011)
10.1080/10255840600751523
Finite element modeling and simulations in orthopedics: a bibliography 1998–2005
J. Mackerle (2006)
10.20381/RUOR-4403
Finite Element Analysis to Examine the Mechanical Stimuli Distributions in the Hip with Cam Femoroacetabular Impingement
K. C. Geoffrey Ng (2011)
Development of Patient-Specific CT-FE Modelling of Bone Through Validation Using Porcine Femora
Nicholas J. Emerson (2012)
10.1088/1742-6596/466/1/012031
Comparison of mechanical behavior between implant-simulated bone tissue and implant-jaw bone tissue interfaces based on Pull Out testing
C López (2013)
10.1016/j.matpr.2020.02.489
Vibration analysis of femur bone by using consistent mass matrices and fast fourier transform analyzer
Balaji D. Kshirsagar (2020)
10.1016/j.medengphy.2010.01.004
Some factors that affect the comparison between isotropic and orthotropic inhomogeneous finite element material models of femur.
Haisheng Yang (2010)
A STUDY OF FLUID-STRUCTURAL COUPLING IN AN OIL- FILLED POWER TRANSFORMER
Yuxing Wang (2018)
10.1016/j.clinbiomech.2014.06.012
Anterior locking plate reduces trochanteric fracture migrations during hip extension.
Luc P. Cloutier (2014)
10.1007/S40846-017-0330-5
Alteration of Strain Distribution in Distal Tibia After Triple Arthrodesis: Experimental and Finite Element Investigations
Ahmad Chitsazan (2018)
10.1080/13588260903047671
A numerical investigation of mid-femoral injury tolerance in axial compression and bending loading
Costin D. Untaroiu (2010)
10.1007/978-3-030-12346-8_18
Topology Optimization Additive Manufacturing-Oriented for a Biomedical Application
Filippo Santi Cucinotta (2019)
10.1007/s10237-008-0122-5
A bone remodelling model including the directional activity of BMUs
J. Martínez-Reina (2009)
Mechanical and adaptive behaviour of bone in relation to hip replacement : a study of bone remodelling and bone grafting.
S. Muller (2005)
10.1016/j.medengphy.2007.12.009
Comparison of an inhomogeneous orthotropic and isotropic material models used for FE analyses.
V. Báča (2008)
10.1109/EMEIT.2011.6023469
The study of the fixation for femoral neck fracture based on finite element method
Monan Wang (2011)
10.1016/j.jcms.2013.06.006
Finite element analysis of type B condylar head fractures and osteosynthesis using two positional screws.
Pengfei Xin (2014)
10.4028/www.scientific.net/KEM.270-273.2067
Evaluation of Dynamic Behavior of the Human Middle Ear with Nonhomogeneity by Finite Element Method
Seung-Hyun Yoo (2004)
10.1016/J.MEDENGPHY.2005.06.003
Comparison of isotropic and orthotropic material property assignments on femoral finite element models under two loading conditions.
L. Peng (2006)
Development of a Novel Revison Total Hip Arthroplasty Method for Femoral Component Extraction
M. Keenan (2013)
10.1016/B978-0-12-803581-8.04017-0
Finite Element Simulation of Fracture Profile of Bone Material: A Case of Study Applied to Human Femur Specimen
Awad Bettamer (2014)
10.1590/1679-78251814
Bone Anisotropy - Analytical and Finite Element Analysis
Lucas Lisbôa Vignoli (2016)
See more
Semantic Scholar Logo Some data provided by SemanticScholar