Online citations, reference lists, and bibliographies.
← Back to Search

Comparison Between A Silorane-based Composite And Methacrylate-based Composites: Shrinkage Characteristics, Thermal Properties, Gel Point And Vitrification Point.

Bo-tao Gao, H. Lin, G. Zheng, Yong-xiang Xu, Jin-liang Yang
Published 2012 · Materials Science, Medicine

Save to my Library
Download PDF
Analyze on Scholarcy
Share
A silorane-based composite was compared against methacrylate-based composites in terms of shrinkage characteristics, thermal properties, gel point, and vitrification point. Shrinkage strain was measured using a laser triangulation method. Shrinkage stress was measured using a stress analyzer. Heat flow during photopolymerization was measured using photo-DSC. Statistical analysis was performed using one-way ANOVA and Tukey's test (p=0.05). Silorane exhibited significantly lower shrinkage strain than the methacrylate-based composites. It also presented the lowest stress values during light exposure, but the highest maximum stress rate after light exposure. It showed the highest heat flow rate, and it took the longest time to reach gel and vitrification points. Silorane demonstrated improved performance over the methacrylate-based composites with delayed gel and vitrification points as well as reduced shrinkage strain and stress. However, a high quantity of heat was liberated during the curing process, causing silorane to show significantly higher stress rate (p<0.05) than the methacrylate-based composites after light exposure.
This paper references
10.1016/j.dental.2010.08.003
Polymerization stress, shrinkage and elastic modulus of current low-shrinkage restorative composites.
L. Boaro (2010)
10.1016/S0109-5641(00)00020-8
Light intensity effects on resin-composite degree of conversion and shrinkage strain.
N. Silikas (2000)
10.1016/j.dental.2009.06.022
Setting characteristics and cavity adaptation of low-shrinking resin composites.
D. Papadogiannis (2009)
10.1016/0022-3913(86)90173-3
Resisting the curing contraction with adhesive composites.
C. Davidson (1986)
10.1016/S0300-5712(96)00063-2
Polymerization shrinkage and polymerization shrinkage stress in polymer-based restoratives.
C. Davidson (1997)
10.1016/j.dental.2010.07.002
Effect of shrinkage strain, modulus, and instrument compliance on polymerization shrinkage stress of light-cured composites during the initial curing stage.
S. Min (2010)
10.1046/J.1365-2842.2001.00639.X
Thermal analysis on the cure speed of dual cured resin cements under porcelain inlays.
I. Lee (2001)
10.1016/S0109-5641(00)00079-8
Polymerization contraction stress in light-cured packable composite resins.
H. Chen (2001)
[A new dynamic approach to monitoring dental composite curing kinetics].
Bo-tao Gao (2011)
10.1016/J.DENTAL.2004.10.006
Conversion-dependent shrinkage stress and strain in dental resins and composites.
J. Stansbury (2005)
10.1016/S0142-9612(01)00308-8
Effect of chemical structure on degree of conversion in light-cured dimethacrylate-based dental resins.
I. Sideridou (2002)
10.1002/JBM.10386
The influence of system compliance and sample geometry on composite polymerization shrinkage stress.
G. Laughlin (2002)
Silorane in dental composites
W Weinmann (2005)
10.1016/j.dental.2010.05.007
Contraction stress of low-shrinkage composite materials assessed with different testing systems.
G. Marchesi (2010)
10.1016/J.DENTAL.2005.04.018
Factors involved in the development of polymerization shrinkage stress in resin-composites: a systematic review.
R. Braga (2005)
Relationship between composite contraction stress and leakage in Class V cavities.
J. Ferracane (2003)
Light intensity effects on resin-composite degree of conversion and contraction strain
N Silikas (2000)
10.1016/J.DENTAL.2007.06.006
Contraction stress and physical properties development of a resin-based composite irradiated using modulated curing methods at two C-factor levels.
L. G. Cunha (2008)
10.1016/0109-5641(90)90023-8
Quantitative determination of stress reduction by flow in composite restorations.
A. Feilzer (1990)
10.1046/J.1365-2842.2002.00866.X
Composite conversion and temperature rise using a conventional, plasma arc, and an experimental blue LED curing unit.
Z. Tarle (2002)
10.1002/PAT.1132
Synthesis and characterization of copolymerizable one‐component type II photoinitiator
Pu Xiao (2008)
10.1016/S0032-3861(99)00758-2
Understanding vitrification during cure of epoxy resins using dynamic scanning calorimetry and rheological techniques
J. Lange (2000)
10.1016/S0142-9612(01)00212-5
Polymerization of dental composite resins using plasma light.
L. Fanò (2002)
10.1016/j.dental.2009.08.001
Influence of curing protocol on selected properties of light-curing polymers: degree of conversion, volume contraction, elastic modulus, and glass transition temperature.
M. Dewaele (2009)
10.1016/S0300-5712(03)00089-7
The influence of plasma arc vs. halogen standard or soft-start irradiation on polymerization shrinkage kinetics of polymer matrix composites.
N. Hofmann (2003)
Polymerization characteristics, flexural modulus and microleakage evaluation of silorane-based and methacrylate-based composites.
Bo-tao Gao (2011)
10.1002/POLA.20012
Photoinduced cationic ring‐opening frontal polymerizations of oxetanes and oxiranes
J. Crivello (2004)
10.1016/J.DENTAL.2006.06.019
The influence of curing times and light curing methods on the polymerization shrinkage stress of a shrinkage-optimized composite with hybrid-type prepolymer fillers.
Anuradha Visvanathan (2007)
10.1016/S0109-5641(03)00097-6
Calculation of contraction rates due to shrinkage in light-cured composites.
C. Alvarez-Gayosso (2004)
10.1111/J.1708-8240.2000.TB00238.X
Developments in shrinkage control of adhesive restoratives.
B. Dauvillier (2000)
10.1111/j.1708-8240.2009.00244.x
Temperature changes in silorane-, ormocer-, and dimethacrylate-based composites and pulp chamber roof during light-curing.
Vesna J Miletic (2009)
10.1177/00220345870660110601
Setting Stress in Composite Resin in Relation to Configuration of the Restoration
A. Feilzer (1987)
10.4012/DMJ.26.149
Low-shrinkage composite for dental application.
N. Ilie (2007)
10.1016/J.DENTAL.2004.10.004
Developing a more complete understanding of stresses produced in dental composites during polymerization.
J. Ferracane (2005)
10.1016/J.DENTAL.2004.10.007
Siloranes in dental composites.
W. Weinmann (2005)



This paper is referenced by
Further development of a novel fluoride releasing acrylic orthodontic adhesive
H. Ismail (2016)
10.7234/COMPOSRES.2013.26.3.182
Polymerization Shrinkage and Stress of Silorane-based Dental Restorative Composite
I. Lee (2013)
10.4067/S0718-381X2018000400395
Adhesion and Initial Colonization of Streptococcus mutans is Influenced by Time and Composition of Different Composites
R. Silva (2018)
Einfluss der "Etch-and-rinse" Technik auf die Dentinhaftung an sklerotischem Dentin
H. Flöttmann (2013)
Einfluss der "Etch-and-rinse" Technik auf die Dentinhaftung an sklerotischem Dentin
Des Fachbereichs Medizin (2013)
10.3844/CRDSP.2014.1.5
Monomers Release from Dental Composites: Effect of Immersion Media and Photoactivation Light Source
R. Silva (2014)
10.1007/s00784-018-2677-6
Clinical evaluation of a low-shrinkage resin composite in endodontically treated premolars: 3-year follow-up
Nihan Gönülol (2018)
10.2341/12-442-L
Incremental filling technique and composite material--part II: shrinkage and shrinkage stresses.
A. A. Bicalho (2014)
10.2341/15-311-LIT
The Silorane-based Resin Composites: A Review.
G. Maghaireh (2017)
Wpływ sposobu wypełniania ubytku na naprężenia skurczowe indukowane przez materiały kompozytowe typu bulkfill
A. Sokołowska (2013)
10.1590/0103-6440201301904
Comparison of silorane and methacrylate-based composites on the polymerization heat generated with different light-curing units and dentin thicknesses.
R. Guiraldo (2013)
10.1590/1678-775720150041
Marginal integrity of restorations produced with a model composite based on polyhedral oligomeric silsesquioxane (POSS)
Luciano Ribeiro Correa (2015)
10.1016/j.jmbbm.2019.103515
A low-shrinkage dental composite with epoxy-polyhedral oligomeric silsesquioxane.
Z. Li (2019)
10.1002/MAME.201700021
Evaluation of Difunctional Vinylcyclopropanes as Reactive Diluents for the Development of Low‐Shrinkage Composites
Yohann Catel (2017)
10.4103/0972-0707.168795
Temperature rise during polymerization of different cavity liners and composite resins
O. Karatas (2015)
Contemporary concepts on composite materials
Z. Tarle (2012)
10.2174/1874210601408010013
The Influence of Zinc Oxide Eugenol (ZOE) and Glass Ionomer (GI) Base Materials on the Microhardness of Various Composite and GI Restorative Materials
Roee Itskovich (2014)
10.1016/j.jdent.2015.09.007
Mechanical properties, shrinkage stress, cuspal strain and fracture resistance of molars restored with bulk-fill composites and incremental filling technique.
Cmp Rosatto (2015)
10.1016/j.dental.2016.07.015
Shrinkage stress kinetics of Bulk Fill resin-based composites at tooth temperature and long time.
D. Kalliecharan (2016)
eview rogress in dimethacrylate-based dental composite echnology and curing efficiency
ulian G. Leprincea (2012)
Effect of polyethylene fiber reinforcement on marginal adaptation of composite resin in Class II preparations.
V. Aggarwal (2018)
10.1016/j.dental.2012.11.005
Progress in dimethacrylate-based dental composite technology and curing efficiency.
J. Leprince (2013)
10.1016/j.jmbbm.2018.03.019
Polymerization shrinkage stress of resin-based dental materials: A systematic review and meta-analyses of composition strategies.
C. T. Meereis (2018)
10.1016/j.jdent.2013.11.016
Experimental and FE displacement and polymerization stress of bonded restorations as a function of the C-Factor, volume and substrate stiffness.
L. Boaro (2014)
Polymerisationseigenschaften von Bulk-Fill Kompositen
Eva Maier (2015)
Methacrylate-Based Composites on t h e Po l yme r i z a t i on Hea t Generated with Different Light-Curing Units and Dentin Thicknesses
R. Guiraldo (2013)
10.11606/D.58.2013.TDE-22072013-112353
AVALIAÇÃO DA CITOTOXICIDADE E EXPRESSÃO DE CITOCINAS INDUZIDAS POR RESINA COMPOSTA FOTOPOLIMERIZÁVEL
D. L. Longo (2013)
Silorane adhesive system: a case report.
V. C. Ruschel (2014)
10.1016/j.dental.2018.08.293
Modulating pH through lysine integrated dental adhesives.
L. Song (2018)
10.1016/J.EURPOLYMJ.2017.11.042
Synthesis and polymerization of vinylcyclopropanes bearing urethane groups for the development of low-shrinkage composites
Yohann Catel (2018)
10.2341/12-441-L
Incremental filling technique and composite material--part I: cuspal deformation, bond strength, and physical properties.
A. Bicalho (2014)
10.2341/12-378-L
Measurement of the internal adaptation of resin composites using micro-CT and its correlation with polymerization shrinkage.
H. Kim (2014)
See more
Semantic Scholar Logo Some data provided by SemanticScholar