Online citations, reference lists, and bibliographies.

Relations Of Mechanical Properties To Density And CT Numbers In Human Bone.

J. Rho, M. C. Hobatho, R. B. Ashman
Published 1995 · Engineering, Medicine

Cite This
Download PDF
Analyze on Scholarcy
Share
Mechanical properties of cortical and cancellous bone from eight human subjects were determined using an ultrasonic transmission technique. Raw computerized tomography (CT) values obtained from scans of the bones in water were corrected to Hounsfield units. The correlations between CT numbers and mechanical property estimated from cortical bone were found to be low (r2 < 0.2), while these relationships for cancellous bone were found to be higher (r2 > 0.6). These results suggest that CT values may be useful in predicting mechanical properties only for cancellous bone. Poor correlations were found between modulus in the radial or circumferential direction and modulus in the superior-inferior direction for cortical bone, whereas good correlations were found between modulus in the anterior-posterior direction or medial-lateral direction and modulus in the S-I direction for cancellous bone. These results indicate that modulus in the radial or circumferential direction could not be predicted from modulus in the S-I direction for cortical bone, but could be predicted for cancellous bone. The predictive capabilities of linear and power models evaluated for cancellous bone alone were approximately equal. However, the power function gives a better fit of data at the low and high density values. The specific relationships, depending on the types of bone, that predict elastic modulus from density and CT numbers were suggested for human cortical and cancellous bone. These specific correlations may help a number of researchers develop more accurate models; however, these hypotheses should be proven by further study.



This paper is referenced by
10.1007/S11242-004-6298-Y
Drained and Undrained Poroelastic Properties of Healthy and Pathological Bone: A Poro-Micromechanical Investigation
C. Hellmich (2005)
10.1016/S1350-4533(03)00138-3
An improved method for the automatic mapping of computed tomography numbers onto finite element models.
F. Taddei (2004)
10.1007/s00198-018-4733-0
Bone fragility after spinal cord injury: reductions in stiffness and bone mineral at the distal femur and proximal tibia as a function of time
I. Haider (2018)
10.1016/J.MEDENGPHY.2007.08.006
Prediction of bone mechanical properties using QUS and pQCT: study of the human distal radius.
M. Muller (2008)
Wspomaganie diagnozowania stanów niebezpiecznych w kości miednicznej człowieka z wykorzystaniem metod komputerowych mechaniki
Antoni John (2010)
Mechanical testing and modelling of a bone-implant construct
Caroline A. Grant (2012)
10.1021/acsomega.0c01168
Development and Characterization of a Biocomposite Material from Chitosan and New Zealand-Sourced Bovine-Derived Hydroxyapatite for Bone Regeneration
Jeffrey C.-N. Huang (2020)
10.1016/j.jmbbm.2018.05.040
Cervical fusion cage computationally optimized with porous architected Titanium for minimized subsidence.
Ahmed Ait Moussa (2018)
10.0001/602
Assessment of bone density after six months from dental implants placement using Computed Tomography
Resha J. Al-Sudani (2014)
On the generation and characterisation of internal micro-architectures
David Raymont (2011)
10.1016/j.arthro.2019.11.119
Bony Ingrowth of Coil-Type Open Architecture Anchors Compared with Screw-Type PEEK Anchors for the Medial Row in Rotator Cuff Repair. A Randomized Controlled Trial.
J. Chahla (2019)
10.1016/j.micron.2018.12.008
Study of the porosity of calcified chicken eggshell using atomic force microscopy and image processing.
Israel Arzate-Vázquez (2019)
A Proposal of Unified Elastic Moduli-Matrix Volume Fraction Law for Porous RVEs
G. Perrella (2009)
Double Experimental Procedure for Model-Specific Finite Element Analysis of the Human Femur and Trabecular Bone
G. García (2013)
10.1007/s00402-007-0293-z
Volumetric measurement of periprosthetic bone remodeling: prospective 5 years follow-up after cemented total hip arthroplasty
R. Burchard (2007)
10.4028/www.scientific.net/AMM.5-6.71
Experimental Evaluation of Physical Properties of Bone Structures
F. Antunes (2006)
10.1038/srep38441
Effects of dose reduction on bone strength prediction using finite element analysis
D. Anitha (2016)
10.1007/978-3-642-58699-6_26
Computer Assisted Surgical Planning and Robotics mit dem CASPAR-System
P. Heeckt (1999)
10.2478/MECENG-2014-0030
The Accuracy of the Reproduction of the Lumbar Spine Elements Following CT and MRI Projections
P. Kroczak (2014)
10.1109/ISBI.2015.7163802
Stress variations owing to single-stance load and sideways fall result in fracture at proximal femur
Tanvir R. Faisal (2015)
10.4172/2157-7552.1000161
Methodological Consideration of Various Intraosseous and Heterotopic Bone Grafts Implantation in Animal Models
Weiguo Xu (2015)
10.1371/journal.pone.0028868
Foot Bone in Vivo: Its Center of Mass and Centroid of Shape
Yifang Fan (2010)
10.2495/978-1-85312-749-6/03
Patient Specific Bone And Joints ModelingAnd Tissue Characterization Derived FromMedical Images
M.-C. Ho Ba Tho (2005)
10.5397/CISE.2015.18.2.86
Evaluation of Focal Bone Mineral Density Using Three-dimensional Measurement of Hounsfield Units in the Proximal Humerus
Young Lae Moon (2015)
10.3389/fmech.2017.00023
Bone Apparent and Material Densities Examined by Cone Beam Computed Tomography and the Archimedes Technique: Comparison of the Two Methods and Their Results
George Adams (2018)
10.1016/j.clinbiomech.2010.12.008
ASB Clinical Biomechanics Award Paper 2010 Virtual pre-operative reconstruction planning for comminuted articular fractures.
T. Thomas (2011)
Innovations in medical image processing for the design of custom medical devices and implants
A. Chinea (2012)
Development of computer system to aid of diagnosis osteoporosis in human hip joint region
A. John (2010)
10.2301/NEUROSONOLOGY.20.89
Time-reversal focusing through the skull : application to High Intensity Focused Ultrasound brain therapy.
M. Pernot (2008)
10.1016/j.jbiomech.2007.11.018
Compressive properties of trabecular bone in the distal femur.
T. Burgers (2008)
10.1016/j.compmedimag.2007.09.001
Influence of anisotropy on peri-implant stress and strain in complete mandible model from CT
Shenghui Liao (2008)
EXPERIMENTAL TESTING AND NUMERICAL SIMULATION OF BONE TISSUE
A. John (2016)
See more
Semantic Scholar Logo Some data provided by SemanticScholar