Online citations, reference lists, and bibliographies.

Dependence Of Yield Strain Of Human Trabecular Bone On Anatomic Site.

E. Morgan, T. M. Keaveny
Published 2001 · Engineering, Medicine

Cite This
Download PDF
Analyze on Scholarcy
Share
Understanding the dependence of human trabecular bone strength behavior on anatomic site provides insight into structure-function relationships and is essential to the increased success of site-specific finite element models of whole bones. To investigate the hypothesis that the yield strains of human trabecular bone depend on anatomic site, the uniaxial tensile and compressive yield properties were compared for cylindrical specimens from the vertebra (n=61), proximal tibia (n=31), femoral greater trochanter (n=23), and femoral neck (n=27) taken from 61 donors (67+/-15years). Test protocols were used that minimized end artifacts and loaded specimens along the main trabecular orientation. Yield strains by site (mean+/-S.D.) ranged from 0.70+/-0.05% for the trochanter to 0.85+/-0.10% for the femoral neck in compression, from 0.61+/-0.05% for the trochanter to 0.70+/-0.05% for the vertebra in tension, and were always higher in compression than tension (p<0.001). The compressive yield strain was higher for the femoral neck than for all other sites (p<0.001), as was the tensile yield strain for the vertebra (p<0.007). Analysis of covariance, with apparent density as the covariate, indicated that inter-site differences existed in yield stress even after adjusting statistically for density (p<0.035). Coefficients of variation in yield strain within each site ranged from only 5-12%, consistent with the strong linear correlations (r(2)=0.94-0.98) found between yield stress and modulus. These results establish that the yield strains of human trabecular bone can differ across sites, but that yield strain may be considered uniform within a given site despite substantial variation in elastic modulus and yield stress.
This paper references
10.1016/S8756-3282(98)00030-1
High-resolution magnetic resonance imaging: three-dimensional trabecular bone architecture and biomechanical properties.
S. Majumdar (1998)
10.1115/1.1338122
Nonlinear behavior of trabecular bone at small strains.
E. Morgan (2001)
10.1016/0021-9290(88)90008-5
On the dependence of the elasticity and strength of cancellous bone on apparent density.
J. Rice (1988)
Mechanistic Approaches to Analysis of Trabecular Bone
Ph. D Tony M. Keaveny (1998)
10.1016/0021-9290(94)90054-X
Differences between the tensile and compressive strengths of bovine tibial trabecular bone depend on modulus.
T. M. Keaveny (1994)
10.1016/S0021-9290(00)00149-4
High-resolution finite element models with tissue strength asymmetry accurately predict failure of trabecular bone.
G. Niebur (2000)
10.3233/THC-1998-65-616
Micro-compression: a novel technique for the nondestructive assessment of local bone failure.
R. Müller (1998)
10.1016/8756-3282(87)90074-3
Biomechanical competence of vertebral trabecular bone in relation to ash density and age in normal individuals.
L. Mosekilde (1987)
10.1016/S0021-9290(98)00057-8
Yield strain behavior of trabecular bone.
D. Kopperdahl (1998)
10.1016/0021-9290(91)90333-I
The underestimation of Young's modulus in compressive testing of cancellous bone specimens.
A. Odgaard (1991)
10.1016/S8756-3282(99)00098-8
The ability of three-dimensional structural indices to reflect mechanical aspects of trabecular bone.
D. Ulrich (1999)
10.1016/S8756-3282(99)00190-8
Constitutive relationships of fabric, density, and elastic properties in cancellous bone architecture.
J. Kabel (1999)
10.1359/jbmr.1999.14.7.1167
Direct Three‐Dimensional Morphometric Analysis of Human Cancellous Bone: Microstructural Data from Spine, Femur, Iliac Crest, and Calcaneus
T. Hildebrand (1999)
10.1016/0021-9290(94)90056-6
Predicting the compressive mechanical behavior of bone.
T. Keller (1994)
10.1016/0021-9290(93)90021-6
Theoretical analysis of the experimental artifact in trabecular bone compressive modulus.
T. M. Keaveny (1993)
10.1016/S8756-3282(97)00122-1
Three-dimensional imaging of trabecular bone using the computer numerically controlled milling technique.
J. D. Beck (1997)
10.1016/S0021-9290(99)00152-9
Prediction of femoral fracture load using finite element models: an examination of stress- and strain-based failure theories.
J. Keyak (2000)
10.1016/0021-9290(94)90053-1
Trabecular bone exhibits fully linear elastic behavior and yields at low strains.
T. M. Keaveny (1994)
10.1115/1.3108433
Errors induced by off-axis measurement of the elastic properties of bone.
C. Turner (1988)
10.1016/S0021-9290(98)00150-X
Tissue stresses and strain in trabeculae of a canine proximal femur can be quantified from computer reconstructions.
B. van Rietbergen (1999)
10.1002/jor.1100090507
Evaluation of orthogonal mechanical properties and density of human trabecular bone from the major metaphyseal regions with materials testing and computed tomography
M. Ciarelli (1991)
10.1115/1.2834756
A global relationship between trabecular bone morphology and homogenized elastic properties.
P. Zysset (1998)
10.1115/1.3168375
Yield behavior of bovine cancellous bone.
C. Turner (1989)
10.1115/1.2798339
A cellular solid criterion for predicting the axial-shear failure properties of bovine trabecular bone.
C. Fenech (1999)
10.1115/1.2895412
Fracture prediction for the proximal femur using finite element models: Part I--Linear analysis.
J. C. Lotz (1991)
10.1016/S8756-3282(99)00246-X
Bone stiffness predicts strength similarly for human vertebral cancellous bone in compression and for cortical bone in tension.
D. Fyhrie (2000)
10.2106/00004623-199703000-00016
Age-Related Changes in the Compressive Strength of Cancellous Bone. The Relative Importance of Changes in Density and Trabecular Architecture*
R. Mccalden (1997)
10.2106/00004623-198567080-00010
Prediction of vertebral body compressive fracture using quantitative computed tomography.
R. Mcbroom (1985)
10.3109/17453678008990819
Mechanical property distributions in the cancellous bone of the human proximal femur.
T. Brown (1980)
10.1002/JOR.1100160305
Computed tomography‐based finite element analysis predicts failure loads and fracture patterns for vertebral sections
M. Silva (1998)
10.2106/00004623-199072050-00008
The use of quantitative computed tomography to estimate risk of fracture of the hip from falls.
J. C. Lotz (1990)
10.2106/00004623-197759070-00021
The compressive behavior of bone as a two-phase porous structure.
D. Carter (1977)
10.1002/JOR.1100150115
Systematic and random errors in compression testing of trabecular bone
T. M. Keaveny (1997)
10.1002/JOR.1100170418
Uniaxial yield strains for bovine trabecular bone are isotropic and asymmetric
W. C. Chang (1999)



This paper is referenced by
10.1016/B978-012470862-4/50002-7
The Bone Organ System: Form and Function
C. Lee (2001)
10.1103/PhysRevB.66.144203
Strength reduction in electrical and elastic networks
J. Ortiz (2002)
10.1007/s00586-005-0915-5
The long-term mechanical integrity of non-reinforced PEEK-OPTIMA polymer for demanding spinal applications: experimental and finite-element analysis
S. Ferguson (2005)
10.1016/B978-012369390-7/50005-8
Biomechanics of Vertebral Bone
T. M. Keaveny (2006)
10.1016/S1672-6529(14)60033-0
Biomechanics of Musculoskeletal System and Its Biomimetic Implications: A Review
Lei Ren (2014)
10.1016/j.jbiomech.2016.09.039
Analysis of an early intervention distal femoral resurfacing implant for medial osteoarthritis.
Miriam Chaudhary (2016)
10.1186/1471-2474-9-137
Compressive properties of commercially available polyurethane foams as mechanical models for osteoporotic human cancellous bone
P. S. Patel (2008)
10.1016/j.bone.2016.06.006
Study of sex differences in the association between hip fracture risk and body parameters by DXA-based biomechanical modeling.
M. Nasiri (2016)
10.1016/J.ENGFRACMECH.2008.12.013
Insights into the effects of tensile and compressive loadings on microstructure dependent fracture of trabecular bone
V. Tomar (2009)
10.1016/j.jmbbm.2011.09.003
On the effect of marrow in the mechanical behavior and crush response of trabecular bone.
J. Halgrin (2012)
10.1016/B978-0-08-100752-5.00012-3
Composite materials for hip joint prostheses
Rosa De Santis (2010)
10.1016/j.clinbiomech.2020.01.017
Load response of an osseointegrated implant used in the treatment of unilateral transfemoral amputation: An early implant loosening case study.
D. Robinson (2020)
Effects of Gamma Irradiation on the Damage Processes in Human Trabecular Bone
Daniel S. Ramsey (2010)
10.1142/S0219519415300033
ASSESSMENT OF OSTEOPOROTIC FEMORAL FRACTURE RISK: FINITE ELEMENT METHOD AS A POTENTIAL REPLACEMENT FOR CURRENT CLINICAL TECHNIQUES
Sven van den Munckhof (2015)
10.1080/10255842.2013.820717
A finite element evaluation of the moment arm hypothesis for altered vertebral shear failure force
Samuel J. Howarth (2015)
10.1016/j.cmpb.2020.105319
Anisotropic computational modelling of bony structures from CT data: An almost automatic procedure
I. Toniolo (2020)
10.1016/j.jmbbm.2019.06.033
Biodegradable nanocomposite Fe-Ag load-bearing scaffolds for bone healing.
A. Sharipova (2019)
Microdamage accumulation in bovine trabecular bone
T. Moore (2001)
10.1007/s10237-013-0486-z
A 3D elastic micropolar model of vertebral trabecular bone from lattice homogenization of the bone microstructure
I. Goda (2014)
10.25560/9190
Effects of Scapular Notching and Bone Remodelling on Long-Term Fixation of the Glenoid Component in Reverse Shoulder Arthroplasty
Min Zhang (2011)
10.1007/s00198-012-2039-1
The effect of intravertebral heterogeneity in microstructure on vertebral strength and failure patterns
A. Hussein (2012)
10.1016/J.JBIOMECH.2004.02.045
Mechanisms of uniformity of yield strains for trabecular bone.
Harun H. Bayraktar (2004)
10.1115/1.4001159
The biomechanical consequence of insufficient femoral component lateralization and exposed cancellous bone in hip resurfacing arthroplasty.
M. Olsen (2010)
10.1016/j.bone.2017.06.021
Relationships among ultrasonic and mechanical properties of cancellous bone in human calcaneus in vitro.
K. Wear (2017)
10.1017/S0952836904005412
Maintenance of bone mass and architecture in denning black bears (Ursus americanus)
Connor K. Pardy (2004)
10.1243/09544119JEIM296
Finite element analysis of cancellous bone failure in the vertebral body of healthy and osteoporotic subjects
A. Boccaccio (2008)
10.1016/j.actbio.2019.12.018
Additively Manufactured Iron-Manganese for Biodegradable Porous Load-Bearing Bone Scaffold Applications.
D. Carluccio (2019)
10.1016/B978-0-12-809831-8.00014-3
Modeling the Thorax for Impact Scenarios
K. Yang (2018)
10.1016/j.jbiomech.2009.09.052
Primary stability of uncemented femoral resurfacing implants for varying interface parameters and material formulations during walking and stair climbing.
Stephan Rothstock (2010)
Experimental and computational study of the behaviour of trabecular bone-cement interfaces.
Sebastien N F Sikora (2013)
10.1016/j.jmrt.2019.12.089
Evaluating compressive properties and morphology of expandable polyurethane foam for use in a synthetic paediatric spine
Nor Amalina Muhayudin (2020)
10.1016/j.engfracmech.2020.107053
Post-yield mechanical properties of bovine trabecular bone – Relationships with bone volume fraction and strain rate
Juan Diego Silva-Henao (2020)
See more
Semantic Scholar Logo Some data provided by SemanticScholar