Online citations, reference lists, and bibliographies.

Research On Semisolid Microstructural Evolution Of 2024 Aluminum Alloy Prepared By Powder Thixoforming

Pubo Li, Tijun Chen, Suqing Zhang, Renguo Guan
Published 2015 · Materials Science

Cite This
Download PDF
Analyze on Scholarcy
Share
A novel method, powder thixoforming, for net-shape forming of the particle-reinforced Aluminum matrix composites in semi-solid state has been proposed based on powder metallurgy combining with thixoforming technology. The microstructural evolution and phase transformations have been investigated during partial remelting of the 2024 bulk alloy, prepared by cold pressing of atomized alloy powders to clarify the mechanisms of how the consolidated powders evolve into small and spheroidal primary particles available for thixoforming. The effect of heating temperature on the resulting semisolid microstructure has also been discussed. The results indicate that the microstructural evolution includes three stages—the initial rapid coarsening of the fine grains within the powders, the formation of continuous liquid layer on the primary particle surface (the original powder), and the final coarsening—that result from the phase transformations of θ→α, α→L, and α→L and L→α, respectively. The coarsening rate of the primary particles is low, and one original powder always evolves into one spheroidal particle with a continuous liquid layer surface. Properly raising the heating temperature is beneficial for obtaining an ideal semisolid microstructure.
This paper references
10.1016/J.MSEA.2005.12.032
Processing and interfacial bonding strength of 2014 Al matrix composites reinforced with oxidized SiC particles
Y. Kim (2006)
10.1016/J.MATDES.2011.11.061
Microstructure evolution and mechanical properties of backward thixoextruded 7075 aluminum alloy
M. Reza Rokni (2012)
10.1179/026708300101508621
Microstructural evolution and semisolid forming of SiC particulate reinforced AZ91HP magnesium composites
T. W. Hong (2000)
10.1007/BF01162502
Nucleation mechanism of the cubic σ phase in squeeze-cast aluminium matrix composites
R. Schueller (1994)
10.1016/J.ACTAMAT.2006.07.015
Sintering of particles of different sizes
H. Ch’ng (2007)
10.1023/A:1004761116824
The effect of extrusion parameters on the fretting wear resistance of Al-based composites produced via powder metallurgy
J. Zhou (1999)
10.1016/J.MSEA.2014.11.059
An investigation into microstructure and mechanical properties of cold sprayed 7075 Al deposition
M. Reza Rokni (2015)
10.1016/S0921-5093(01)01401-0
Morphological evolution of SSM A356 during partial remelting
E. J. Zoqui (2002)
10.1023/A:1017572624976
Fabrication of TiAl by blended elemental powder semisolid forming
C. Wen (2001)
10.11890/1006-7191-101-21
Strengthening and toughening forming of Al/Al2O3 composite in pseudo-semi-solid state
Cheng Yuan-Qing (2010)
10.1016/J.SURFCOAT.2014.04.035
Microstructural evolution of 7075 Al gas atomized powder and high-pressure cold sprayed deposition
M. Rokni (2014)
10.1007/S11661-007-9153-2
The Effect of Particle Shape on the Sintering of Aluminum
Z. Liu (2007)
10.1115/1.2400271
Development of Short Fiber-Reinforced NiTi∕Al6061 Composite
C. L. Xie (2007)
This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution license (http://creativecommons
10.1016/S1003-6326(06)60324-5
Pseudo-semi-solid thixoforging of cup shell with Al/Al2O3
Shou-jing Luo (2006)
10.1016/J.ACTAMAT.2010.04.036
Fabrication of Al6061 composite with high SiC particle loading by semi-solid powder processing
Y. Wu (2010)
10.1016/S0921-5093(00)00907-2
A comparative characterization of near-equiaxed microstructures as produced by spray casting, magnetohydrodynamic casting and the stress induced, melt activated process
E. Tzimas (2000)
10.1016/S0266-3538(99)00106-2
Tribological behavior of self-lubricating aluminium/SiC/graphite hybrid composites synthesized by the semi-solid powder-densification method
M.L.Ted Guo (2000)
10.1016/S0921-5093(00)01656-7
Microstructural characterization and tensile properties of hot pressed Al–SiC composites prepared from pure Al and Cu powders
B. Ögel (2001)
10.1361/10599490420034
Effects of isothermal heat treatment on microstructural evolution of semisolid Al-4Cu-Mg alloy
J. Hai-tao (2004)
10.1016/J.JMATPROTEC.2005.06.037
The effect of mechanical alloying on SiC distribution and the properties of 6061 aluminum composite
N. Zhao (2005)
10.1016/J.JALLCOM.2010.06.106
Effect of initial as-cast microstructure of AZ91D magnesium alloy on its semisolid microstructure
T. Chen (2010)
10.1016/J.JMATPROTEC.2007.08.044
Preparation, microstructures and deformation behavior of SiCP/6066Al composites produced by PM route
N. Cheng (2008)
10.1016/S1359-6454(01)00221-X
Effect of limited matrix–reinforcement interfacial reaction on enhancing the mechanical properties of aluminium–silicon carbide composites
L. M. Tham (2001)
Desk handbook phase diagrams for binary alloys
岡本 博明 (2000)
10.1016/S1359-6454(00)00036-7
THE DEVELOPMENT OF SPATIAL CORRELATIONS DURING OSTWALD RIPENING: A TEST OF THEORY
V. Snyder (2000)
10.1002/SIA.1087
Determining the role of surfaces and interfaces in the powder metallurgy processing of aluminum alloy powders
I. Anderson (2001)
10.1016/J.JALLCOM.2010.03.090
Microstructural evolution and phase transformations during partial remelting of AZ91D magnesium alloy refined by SiC
T. Chen (2010)
10.1361/10599490417597
Crack propagation resistance along strength mismatched bimetallic interface
F. Jiang (2004)
10.1016/S0921-5093(98)00855-7
The interfacial reaction characteristics in SiC/Al composite above liquidus during remelting
T. Fan (1998)



This paper is referenced by
10.1016/J.MATDES.2016.07.042
Blended powder semisolid forming of Al7075/Al2O3 composites: Investigation of microstructure and mechanical properties
Akbar Javdani (2016)
10.3390/MET7100416
Effect of Y Addition on the Semi-Solid Microstructure Evolution and the Coarsening Kinetics of SIMA AZ80 Magnesium Alloy
Q. Tang (2017)
10.1007/s10853-016-0493-4
Effects of pressure on microstructure and mechanical properties of SiCp/2024 Al-based composites fabricated by powder thixoforming
Pubo Li (2016)
10.2320/MATERTRANS.M2016070
Effects of Partial Remelting on Microstructure of Al-Si-Ti Bulk Alloy Prepared by Cold Pressing Mixed Powders
Yi Wang (2016)
10.1007/s12540-017-6363-z
Effects of reheating time on microstructure and tensile properties of SiCp/2024 Al-based composites fabricated using powder thixoforming
Pu Bo Li (2017)
10.1016/J.MSEA.2014.01.095
Influences of hot-isostatic-pressing temperature on microstructure, tensile properties and tensile fracture mode of Inconel 718 powder compact
Litao Chang (2014)
10.2320/MATERTRANS.M2015367
Microstructural Evolution during Partial Remelting of a 2024 Aluminum Alloy Prepared by Cold Pressing Ball-Milled Alloy Powders
Pu Bo Li (2016)
10.1007/s10853-017-1713-2
Effects of reheating duration on the microstructure and tensile properties of in situ core–shell-structured particle-reinforced A356 composites fabricated via powder thixoforming
Tuan Jie Chen (2017)
10.1016/j.jallcom.2020.153815
Hierarchical microstructure architecture: A roadmap towards strengthening and toughening reduced graphene oxide/2024Al matrix composites synthesized by flake powder thixoforming
P. Li (2020)
10.1007/s12598-020-01396-3
Semisolid microstructural evolution of (CNTs + Sip)/AZ91D powder compacts prepared from powders by cold pressing and remelting
P. Li (2020)
10.1557/JMR.2017.95
The microstructure and mechanical properties of Al2024-SiCp composite fabricated by powder thixoforming
Pubo Li (2017)
10.3390/ma9030199
Semisolid Microstructural Evolution during Partial Remelting of a Bulk Alloy Prepared by Cold Pressing of the Ti-Al-2024Al Powder Mixture
Yahong Qin (2016)
10.1557/JMR.2016.293
Effect of SiCp volume fraction on the microstructure and tensile properties of SiCp/2024 Al-based composites prepared by powder thixoforming
Li Pubo (2016)
10.3390/MET7100408
Tensile Properties and Fracture Behavior of a Powder-Thixoformed 2024Al/SiCp Composite at Elevated Temperatures
Pubo Li (2017)
10.3390/MET6010015
Casting Alloy Design and Modification
Anders E. W. Jarfors (2016)
10.3390/MET5021112
Study on Dual Modification of Al-17%Si Alloys by Structural Heredity
Jing Zhang (2015)
10.1007/s40195-016-0482-2
Influences of Hot-Isostatic-Pressing Temperature on the Microstructure, Tensile Properties and Tensile Fracture Mode of 2A12 Powder Compact
G. Wang (2016)
10.1590/1980-5373-MR-2016-0466
Effects of Processing Parameters on Microstructure and Mechanical Properties of Powder-Thixoforged SiC p /6061 Al Composite
Chi Cao (2017)
10.1088/2053-1591/ab4c5b
Study of microstructure and mechanical properties of aluminum 7075 alloy extruded in a semi-solid state
Kamran Hajihassani (2019)
10.1080/00325899.2016.1210279
Effect of reheating temperature on the microstructure and tensile properties of SiCP/2024Al composite prepared by powder thixoforming
Pubo Li (2016)
10.3390/MET6030042
Phase Evolution and Mechanical Behavior of the Semi-Solid SIMA Processed 7075 Aluminum Alloy
Behzad Binesh (2016)
10.3390/ma9060407
A Comparative Study on Permanent Mold Cast and Powder Thixoforming 6061 Aluminum Alloy and Sicp/6061Al Composite: Microstructures and Mechanical Properties
Xuezheng Zhang (2016)
10.1155/2017/7967848
Synthesis and Characterization of Zn-Nix Advanced Alloys Prepared by Mechanical Milling and Sintering at Solid-State Process
José G. Miranda-Hernández (2017)
10.1016/J.MATDES.2016.03.068
Effects of solution treatment on tensile properties and strengthening mechanisms of SiCp/6061Al composites fabricated by powder thixoforming
Xuan Zhang (2016)
Semantic Scholar Logo Some data provided by SemanticScholar